Changes between Version 15 and Version 16 of Hardware/jCM/dCM3/bHardware


Ignore:
Timestamp:
06/14/11 14:44:56 (8 years ago)
Author:
Ilya Chigirev
Comment:

--

Legend:

Unmodified
Added
Removed
Modified
  • Hardware/jCM/dCM3/bHardware

    v15 v16  
    99 ==== Lantronix XPort AR ====
    1010The Xport AR is an embedded device server, produced by Lantronix. It runs off of the [http://www.lantronix.com/device-networking/utilities-tools/evolution.html Evolution OS®], combined with the custom software written using the Xport AR SDK. The Xport AR acts as the 'brains' of the CM3, handling all the networking tasks, as well the link between the CMC instruction commands, and the physical interface to the node. It has the following basic features:
    11 || '''Architecture'''||                                                             ||
     11||                              '''Architecture'''                                  ||
    1212||CPU              || Based on the DSTni-EX enhanced 16-bit, 120MHz x86 Architecture||
    13 ||Memory           || 1.25 MB RAM and 4 MB FLASH||
    14 ||Firmware         || upgradeable via FTP,TFTP, Serial Ports, Internal Web Server||
    15 ||Diagnostics      || Built in diagnostics and comprehensive statistics||
    16 ||'''Network Interface'''||
    17 ||Interface        || Ethernet 10Base-T or 100Base-TX (Auto-Sensing)||
    18 ||Connector        || RJ45||
    19 ||Layer 3 Protocols|| TCP, UDP, IP, ARP, ICMP, SSH, SSL, XML, HTTP, [[BR]] PPP, PAP, CHAP, DNS, SMTP, RSS, DHCP, BOOTP, AutoIP, SNMP, [[BR]] FTP, TFTP, Telnet, CGI ||
    20 ||'''Serial Interface''' ||
    21 ||Interface        || CMOS (Asynchronous, 5V Tolerant)||
    22 ||Data Rates       || 300 bps to 230,400 bps (selectable by 1bps increments)||
    23 ||Characters       || 7 or 8 data bits||
    24 ||Parity           || Odd, even, none||
    25 ||Stop Bits        || 1 or 2||
    26 ||Control Signals  || RTS, CTS, DSR, any PIO||
    27 ||Flow Control     || XON/XOFF, RTS/CTS, User Selectable Characters||
     13||Memory           || 1.25 MB RAM and 4 MB FLASH                                    ||
     14||Firmware         || upgradeable via FTP,TFTP, Serial Ports, Internal Web Server   ||
     15||Diagnostics      || Built in diagnostics and comprehensive statistics             ||
     16||                          '''Network Interface'''                                 ||
     17||Interface        || Ethernet 10Base-T or 100Base-TX (Auto-Sensing)                ||
     18||Connector        || RJ45                                                          ||
     19||Layer 3 Protocols|| TCP, UDP, IP, ARP, ICMP, SSH, SSL, XML, HTTP, [[BR]]
     20                      PPP, PAP, CHAP, DNS, SMTP, RSS, DHCP, BOOTP, [[BR]]
     21                      AutoIP, SNMP, FTP, TFTP, Telnet, CGI                          ||
     22||                         '''Serial Interface'''                                   ||
     23||Interface        || CMOS (Asynchronous, 5V Tolerant)                              ||
     24||Data Rates       || 300 bps to 230,400 bps (selectable by 1bps increments)        ||
     25||Characters       || 7 or 8 data bits                                              ||
     26||Parity           || Odd, even, none                                               ||
     27||Stop Bits        || 1 or 2                                                        ||
     28||Control Signals  || RTS, CTS, DSR, any PIO                                        ||
     29||Flow Control     || XON/XOFF, RTS/CTS, User Selectable Characters                 ||
     30
    2831The GPIOs are used to control the solid state relays used to power the node on/off and reset the node, as well as monitor the 'hardware status', see the next section for details on this.
    2932